Anton Peteh
2. pol. 20. st.
, Petešljari (Žminj)
Wood, Woodturning, Hand made
chanter | stock | reeds | ||
A=170 | E1=68 | F=5 | H=58 | d1=46 |
B=23 | E2=17 | G=4 | I=56 | Ø1=5 |
C1=34 | E3=17 | J=54 | d2=46 | |
C2=18,5 | E4=17 | Ø2=5 | ||
D=14 |
The right pipe of the instrument has four finger-holes, and the left one three. The stock is slightly concave on the front and on the rear side. The concavity slightly and gently spreads towards the chanters. The instrument is completely handmade and it doesn't have any decoration.
Božidar Oplanić
oko 1960.
, Jakovići (Tinjan) / Beograd
Wood, Woodturning, Hand made
chanter | stock | reeds | ||
A=178 | E1=77 | F= 7 | H=71 | d1= 55 |
B=18 | E2=15 | G=4,5 (5,5) | I=58 | Ø1= 7,5 |
C1=30 | E3=17 | J=40 | d2= 56 | |
C2=14 | E4=17 | Ø2= 8 | ||
D=10,5 | E5=21 |
The right pipe of the instrument has four holes, and the left one three. The lowest hole on each tube serves as the “flea-hole”. On the right pipe there is a thumb hole drilled a little higher than usual and thus has a melodic function. The stock has ring decorations. The instrument is coloured in yellowish and red tint.
Đuro Adamović
1996.
, Zagreb
Wood, Woodturning
chanter | stock | reeds | ||
A=165 | E1=62 | F=5 | H=64 | d1=48 |
B=19 | E2=20 | G=4 | I=51 | Ø1=6 |
C1=30,5 | E3=20 | J=44 | d2=48 | |
C2=16 | E4=20 | Ø2=6 | ||
D=12 |
La canna destra ha quattro fori digitali sul lato anteriore e quella sinistra tre. Sulla canna destra, parallelamente con il primo, è traforato il foro per il pollice. Lo strumento è decorato molto semplicemente sul blocco con un paio di anelli paralleli fatti sul tornio col filo rovente. Dentro il blocco ci sono gli iniziali del costruttore "Đ.A.". Lo strumento non è masi stato usato.
Anonymous
1968.
Wood, Skin, Rope, Bone, Woodturning, Hand made
chanter | stock | reeds | ||
A=158 | E1=57 | F=7 | H=70 | d1=46 |
B=25 | E2=17,5 | G=4 | I=69 | Ø1=5 |
C1=34 | E3=18 | J=60 | d2=/ | |
C2=17 | E4=17,5 | Ø2=/ | ||
D=11 |
The right pipe of the instrument has four holes, and the left one three. The stock is decorated with protrusions while the pipes have parallel rings and proutrusions made on lathe. The blowpipe is made of sheep's bone. The stock and the blowpipe are tied to the bag on the outer side. One reed is missing.
Anonymous
2.pol. 19. st./sec. meta' 19. sec/2nd half 19th cent.
Wood, Skin, Rope, Bone, Metal, Woodturning, Hand made, Leather processing
chanter | stock | reeds | ||
A=155 | E1=51 | F=6 | H=63 | d1=44 |
B=20 | E2=20 | G=4,5 | I=55,5 | Ø1=6,8 |
C1=20 | E3=20 | J=42 | d2=44 | |
C2=19 | E4=20 | Ø2=6,8 | ||
D=12 | E5=20 |
The right pipe of the instrument has five holes, and the left one four. The lowest hole on each tube serves as the vent-hole. The chanter was entirely handmade while the stock was made later on the lathe. The instrument is decorated with carved ornaments and the stock has parallel rings made on the lathe. The blowpipe is made of animal bone. The bag is tied with a rope and the three small holes are closed with screws.
Martin Glavaš
1983.
, Pula
Wood, Woodturning
chanter | stock | reeds | ||
A=165 | E1=63 | F=7 | H=56,5 | d1=43 |
B=20 | E2=19 | G=4 | I=56,5 | Ø1=6,6 |
C1=29 | E3=19 | J=62 | d2=43 | |
C2=18,5 | E4=19,5 | Ø2=6,6 | ||
D=14,5 |
The right pipe of the instrument has four finger-holes, and the left one three. On the back side of the right pipe there is another finger-hole. The pipes are decorated with parallel rings made with an incandescent wire on a lathe. The stock has also some circular ornaments, and protrusions and grooves made on a lathe. The šurle are lacquered with transparent varnish.
Božidar Oplanić
1969.
Wood, Rope, Goat skin, Rubber, Woodturning, Hand made
chanter | stock | reeds | ||
A=210 | E1=89 | F= / | H= | d1= / |
B=18 | E2=19,5 | E7=69 | I= | Ø1= / |
C1=32 | E3=22 | F=6 | J= | d2= / |
C2=16 | E4=23 | G=4 | Ø2= / | |
D=9,5 | E5=19,5 |
The right pipe of the instrument has five holes, and the left one four. The lowest hole on each tube serves as the vent-hole. On the right pipe there is a thumb hole drilled a little higher than usual and thus has a melodic function. The thumb hole was drilled later and the earlier, the original one was capped with a wooden stopper and wax. The chanter is noticeably larger than the other specimens. The left pipe is cracked at the top and it was clogged with wax and stitched with wire. The bag is made of goatskin. The blowpipe has an inserted piece of rubber tubing, and one leg is blocked with a wooden stopper. The instrument is painted brown.
Anton Peteh
oko 1970.
, Petešljari (Žminj)
Wood, Cane, Metal, Woodturning, Hand made
chanter | stock | reeds | ||
A=175 | E1=73 | F=5,7 | H=57 | d1=45 |
B=25 | E2=18 | G=4 | I=52 | Ø1=6 |
C1=32 | E3=20 | J=46 | d2=40 | |
C2=18 | E4=23 | Ø2=5,5 | ||
D=13 |
The right pipe of the instrument has four finger-holes, and the left one three. Already during the manufacture the left pipe was cracked and was therefore reinforced with iron rings. The stock is slightly concave on the front and on the rear side. The concavity slightly and gently spreads towards the chanters. The entire instrument is hand-decorated with dots and cruciform and parallel lines that create geometric motifs. The decorations are made with an incandescent wire. The pipes are made on a lathe, while the stock is completely handmade.
Martin Glavaš
1973.
, Pula
Wood, Cane, Olive, Woodturning
chanter | stock | reeds | ||
A=162 | E1=69 | F=6 | H=60 | d1=46 |
B=22 | E2=20 | G=4 | I=56 | Ø1=5,5 |
C1=28 | E3=20 | J=45 | d2=43 | |
C2=14 | E4=20 | Ø2=6,5 | ||
D=11 |
The right pipe of the instrument has four finger-holes, and the left one three. The pipes are decorated with parallel rings made with an incandescent wire on a lathe. The stock also has ring ornaments, and protrusions and grooves made on a lathe. There is a marked spot for a hole that was not drilled on the left pipe, in line with the first hole on the right pipe. The šurle are lacquered with transparent varnish.
Martin Glavaš
1973.
, Pula
Wood, Cane, Woodturning
chanter | stock | reeds | ||
A=163 | E1=68 | F=6 | H=59 | d1=44 |
B=21 | E2=20 | G=4 | I=53 | Ø1=6 |
C1=27 | E3=20 | J=46 | d2=45 | |
C2=14 | E4=20 | Ø2=6 | ||
D=11 |
The right pipe of the instrument has four finger-holes, and the left one three. The pipes are decorated with two parallel rings made with an incandescent wire on a lathe. The stock also has ring ornaments, and protrusions and grooves made on a lathe. The šurle are almost invisibly lacquered with transparent varnish.
Anton Peteh
1973.
, Petešljari (Žminj)
Wood, Cane, Hand made
chanter | stock | reeds | ||
A=163 | E1=61 | F=5 | H=64 | d1=46 |
B=21 | E2=19,5 | G=4 | I=51 | Ø1=5,5 |
C1=28 | E3=18 | J=50 | d2=46 | |
C2=19 | E4=20 | Ø1=5,5 | ||
D=15 |
The right pipe of the instrument has four finger-holes, and the left one three. The stock is slightly concave on the front and on the rear side. The concavity slightly and gently spreads towards the chanters. The front side of the instrument is hand-decorated with cruciform and parallel lines which seem to be positioned asymmetrically. The instrument is completely handmade.
Martin Glavaš
1974.
, Pula
Wood, Cane, Woodturning
chanter | stock | reeds | ||
A=53 | E1=60 | F=6 | H=60 | d1=46,5 |
B=13 | E2=19 | G=4 | I=54 | Ø1=6,7 |
C1=25 | E3=19 | J=39 | d2=48,5 | |
C2=11,5 | E4=20 | Ø1=6,4 | ||
D=10,5 |
The right pipe of the instrument has four finger-holes, and the left one three. There are no indentations for fingers on the chanters. The pipes are decorated with grooves made on a lathe and parallel rings made with an incandescent wire also with the help of a lathe. The stock also has ring decorations. The šurle are lacquered with transparent varnish..
Martin Glavaš
1990.
, Pula
Wood, Cane, Woodturning
chanter | stock | reeds | ||
A=162 | E1=57 | F=6 | H=62 | d1=49 |
B=18 | E2=17,5 | G=4 | I=58 | Ø1=6,5 |
C1=30 | E3=19 | J=50 | d2=48 | |
C2=16,7 | E4=19 | Ø1=6,3 | ||
D=14 |
The right pipe of the instrument has four finger-holes on the front side, and the left one has three. A thumb hole is drilled on the right pipe in line with the first one. The instrument is very simply decorated on the upper part of the pipes with two parallel rings made with an incandescent wire on a lathe. The šurle are lacquered with transparent varnish. The stock bears the initials of the maker - MG – carved with an incandescent tin stamp.
Anton Peteh
1963.
, Petešljari (Žminj)
Wood, Cane, Metal, Woodturning, Hand made
chanter | stock | reeds | ||
A=170 | E1=67 | F=5,5 | H=61 | d1=42 |
B=25 | E2=21 | G=3,5 | I=55 | Ø1=6 |
C1=34 | E3=22 | J=45 | d2=43 | |
C2=18 | E4=22 | Ø2=5,5 | ||
D=13 |
The right pipe of the instrument has four holes, and the left one three. Already during the manufacture the left pipe was cracked and was therefore reinforced with iron rings. The stock is slightly concave on the front and on the rear. The concavity slightly and gently spreads towards the chanters. The lower part of the stock is carved with notched decorations. The entire instrument is hand-decorated with dots and cruciform and parallel lines that create geometric motifs. The decorations are made with an incandescent wire. The pipes are made on a lathe, while the stock is completely handmade.
Alfonso Konović
1990.
, Barban
Wood, Cane, Woodturning, Hand made
chanter | stock | reeds | ||
A=170 | E1=76 | F=7,3 (pipe down) | H=60 | d1=41 |
B=17 | E2=21 | 5,7 (pipe down) | I=55 | Ø1=6 |
C1=47 | E3=21 | G=3 | J=40 | d2=49 |
C2=38 (middle) | E4=21 | Ø1=6 | ||
D=26 |
This instrument is šurle with a monoxyle chanter. The right pipe has four finger-holes on the front side and the left one has three. A thumb hole is drilled on the right pipe in line with the first hole. At the bottom of the instrument there are crossed and stripped carved decorations. The stock is decorated with parallel rings made with an incandescent wire on a lathe. The maker, Alfonso Konović, made the instrument to mirror the ancient šurle, also known as "double mišnice", which almost came out of use. The šurle are lacquered with transparent varnish.
Nepoznat
oko/cca 1970
Wood, Woodturning
chanter | stock | reeds | ||
A=170 | E1=65 | F=6 | H=58 | d1=52 |
B=22 | E2=20 | G=4 | I=44 | Ø1=6 |
C1=28 | E3=20 | J=41 | d2=52 | |
C2=15 | E4=22 | Ø2=6 | ||
D=11 |
The right pipe of the instrument has four holes, and the left one three. The pipes are decorated with parallel rings made with an incandescent wire on a lathe. The stock also has ring ornaments, and protrusions and grooves made on a lathe. The instrument is lacquered with transparent varnish. The bottom of the pipes is enlarged in conical shape. The instrument was acquired in Motovun in 1972 on a local fair. Fedor (or Ferdo) Kritovac bought and used this instrument.
Anton Peteh
2. pol. 20. st.
, Petešljari (Žminj)
Wood, Woodturning, Hand made
chanter | stock | reeds | ||
A=170 | E1=68 | F=5 | H=58 | d1=46 |
B=23 | E2=17 | G=4 | I=56 | Ø1=5 |
C1=34 | E3=17 | J=54 | d2=46 | |
C2=18,5 | E4=17 | Ø2=5 | ||
D=14 |
The right pipe of the instrument has four finger-holes, and the left one three. The stock is slightly concave on the front and on the rear side. The concavity slightly and gently spreads towards the chanters. The instrument is completely handmade and it doesn't have any decoration.
Božidar Oplanić
oko 1960.
, Jakovići (Tinjan) / Beograd
Wood, Woodturning, Hand made
chanter | stock | reeds | ||
A=178 | E1=77 | F= 7 | H=71 | d1= 55 |
B=18 | E2=15 | G=4,5 (5,5) | I=58 | Ø1= 7,5 |
C1=30 | E3=17 | J=40 | d2= 56 | |
C2=14 | E4=17 | Ø2= 8 | ||
D=10,5 | E5=21 |
The right pipe of the instrument has four holes, and the left one three. The lowest hole on each tube serves as the “flea-hole”. On the right pipe there is a thumb hole drilled a little higher than usual and thus has a melodic function. The stock has ring decorations. The instrument is coloured in yellowish and red tint.
Đuro Adamović
1996.
, Zagreb
Wood, Woodturning
chanter | stock | reeds | ||
A=165 | E1=62 | F=5 | H=64 | d1=48 |
B=19 | E2=20 | G=4 | I=51 | Ø1=6 |
C1=30,5 | E3=20 | J=44 | d2=48 | |
C2=16 | E4=20 | Ø2=6 | ||
D=12 |
La canna destra ha quattro fori digitali sul lato anteriore e quella sinistra tre. Sulla canna destra, parallelamente con il primo, è traforato il foro per il pollice. Lo strumento è decorato molto semplicemente sul blocco con un paio di anelli paralleli fatti sul tornio col filo rovente. Dentro il blocco ci sono gli iniziali del costruttore "Đ.A.". Lo strumento non è masi stato usato.
Anonymous
1968.
Wood, Skin, Rope, Bone, Woodturning, Hand made
chanter | stock | reeds | ||
A=158 | E1=57 | F=7 | H=70 | d1=46 |
B=25 | E2=17,5 | G=4 | I=69 | Ø1=5 |
C1=34 | E3=18 | J=60 | d2=/ | |
C2=17 | E4=17,5 | Ø2=/ | ||
D=11 |
The right pipe of the instrument has four holes, and the left one three. The stock is decorated with protrusions while the pipes have parallel rings and proutrusions made on lathe. The blowpipe is made of sheep's bone. The stock and the blowpipe are tied to the bag on the outer side. One reed is missing.
Anonymous
2.pol. 19. st./sec. meta' 19. sec/2nd half 19th cent.
Wood, Skin, Rope, Bone, Metal, Woodturning, Hand made, Leather processing
chanter | stock | reeds | ||
A=155 | E1=51 | F=6 | H=63 | d1=44 |
B=20 | E2=20 | G=4,5 | I=55,5 | Ø1=6,8 |
C1=20 | E3=20 | J=42 | d2=44 | |
C2=19 | E4=20 | Ø2=6,8 | ||
D=12 | E5=20 |
The right pipe of the instrument has five holes, and the left one four. The lowest hole on each tube serves as the vent-hole. The chanter was entirely handmade while the stock was made later on the lathe. The instrument is decorated with carved ornaments and the stock has parallel rings made on the lathe. The blowpipe is made of animal bone. The bag is tied with a rope and the three small holes are closed with screws.
Martin Glavaš
1983.
, Pula
Wood, Woodturning
chanter | stock | reeds | ||
A=165 | E1=63 | F=7 | H=56,5 | d1=43 |
B=20 | E2=19 | G=4 | I=56,5 | Ø1=6,6 |
C1=29 | E3=19 | J=62 | d2=43 | |
C2=18,5 | E4=19,5 | Ø2=6,6 | ||
D=14,5 |
The right pipe of the instrument has four finger-holes, and the left one three. On the back side of the right pipe there is another finger-hole. The pipes are decorated with parallel rings made with an incandescent wire on a lathe. The stock has also some circular ornaments, and protrusions and grooves made on a lathe. The šurle are lacquered with transparent varnish.
Božidar Oplanić
1969.
Wood, Rope, Goat skin, Rubber, Woodturning, Hand made
chanter | stock | reeds | ||
A=210 | E1=89 | F= / | H= | d1= / |
B=18 | E2=19,5 | E7=69 | I= | Ø1= / |
C1=32 | E3=22 | F=6 | J= | d2= / |
C2=16 | E4=23 | G=4 | Ø2= / | |
D=9,5 | E5=19,5 |
The right pipe of the instrument has five holes, and the left one four. The lowest hole on each tube serves as the vent-hole. On the right pipe there is a thumb hole drilled a little higher than usual and thus has a melodic function. The thumb hole was drilled later and the earlier, the original one was capped with a wooden stopper and wax. The chanter is noticeably larger than the other specimens. The left pipe is cracked at the top and it was clogged with wax and stitched with wire. The bag is made of goatskin. The blowpipe has an inserted piece of rubber tubing, and one leg is blocked with a wooden stopper. The instrument is painted brown.
Anton Peteh
oko 1970.
, Petešljari (Žminj)
Wood, Cane, Metal, Woodturning, Hand made
chanter | stock | reeds | ||
A=175 | E1=73 | F=5,7 | H=57 | d1=45 |
B=25 | E2=18 | G=4 | I=52 | Ø1=6 |
C1=32 | E3=20 | J=46 | d2=40 | |
C2=18 | E4=23 | Ø2=5,5 | ||
D=13 |
The right pipe of the instrument has four finger-holes, and the left one three. Already during the manufacture the left pipe was cracked and was therefore reinforced with iron rings. The stock is slightly concave on the front and on the rear side. The concavity slightly and gently spreads towards the chanters. The entire instrument is hand-decorated with dots and cruciform and parallel lines that create geometric motifs. The decorations are made with an incandescent wire. The pipes are made on a lathe, while the stock is completely handmade.